Latex·ite® Pli-Stix® 30ft. MEDIUM 1/2" Black Permanent Asphalt Crack Filler

PliStix 2015
360 PliStix 2015 Melt it Pack it Small Crack-done Black rope

Latex·ite® Pli-Stix® 30ft. MEDIUM 1/2″ Black Permanent Asphalt Crack Filler

Latex·ite® PLI-STIX® 30 ft. MEDIUM  1/2″ Black Permanent Asphalt Crack Filler is the only PERMANENT solution to cracks on the marketplace. It is the same product seen on highways and roads but the only difference is YOU CAN APPLY IT and don’t need a 200 gallon melter to do it! The Medium Pli-Stix® is designed for cracks 1/2″ to 1″ in diameter.

 

PLI-STIX® is permanent because it is applied with heat (a simple hand held torch) and it bonds to the sidewalls of the crack. Cracks open up because they expand and contract with freeze/thaw cycles – but PLI-STIX® will expand and contract right along with mother nature!

(Note: PLI-STIX® and CRACK-STIX® are the same product. Pli-Stix® comes in 30ft rolls, while Crack-Stix® comes in longer rolls: 75 ft or 125 ft.)

 

  • Only permanent crack filler on the marketplace.
  • For Cracks 1/2″ – 1″ in diameter.
  • Hot applied, black “rope-like” filler bonds to sidewalls.
  • 30 ft. of MEDIUM PLI-STIX®
  • No VOC’s
  • Prevent slip, trip and fall accidents
  • Packaging is Type #1 PET plastic and IS recyclable
  • Ready to use immediately, melt-away wrapper!
  • Save time and purchase either our CSX-900 Cane Torch extender our really speed up application with our NEW walk behind CSX-1000 PRO MELT TORCH!
  • TIP: If you are not using our recommended torch and are using just a handheld torch it can be difficult to keep the torch upright (or it may flame out)…so you may want to find BURNER WAND which will keep the flame running!
  • For deep cracks or joints, before you begin fill the crack using backer rod, sand or stone dust but leave enough room for product
  • You can use a larger 20lb propane tank to apply but you will need an attachment

 

 

To order from our featured dealer, please visit the product page here.

$13.48

TECHNICAL INFORMATION

  

HOW TO VIDEO
APPLICATION

PLI-STIX® is a simple and clean process. Before applying the product, it is important to thoroughly clean out the crack and remove any loose debris. Rinsing the crack and allowing it to dry will give you the best results.

Now you are ready to install the PLI-STIX®. Simply place the PLI-STIX® into the crack (do not remove the plastic wrap from the PLI-STIX®). The PLI-STIX® must be inside the crack so we recommend pushing the PLI-STIX® into the crack using a screwdriver. (*Note: If the crack is not as wide as the ½" PLI-STIX®, we recommend stretching the PLI-STIX® out...you can leave it in the sun for a while to make it easier to stretch. You can also splice it with a razor blade. You can also use a rubber mallet to help form the strip for the pavement cracks & also helped in the "wedging in" effort). If you have VERY narrow crack you may have to heat a knife with your torch so that it splices the Stix like a butter knife!

Once it's in simply light your torch (we recommend a Bernzomatic hand-held torch) and apply direct flame to the PLI-STIX® until it liquifies - this should take about 20 - 30 seconds. Allow the PLI-STIX® to set up for 20 minutes. PLI-STIX® can be sealed over once properly set up. For best results use CSX Cane TorchTM 900 as this will save you from bending over (it has a crimped end for a nice tight flame). A torch is recommended versus a heat gun but you CAN use a heat gun if your prefer: We recommend an industrial heat gun and temperature must be a minimum of 250 degrees F for it to melt.

Do not apply in wet cracks or where frost, snow or ice is present. Do not apply if the ground temperature is below 40 degrees.

>>> Reminder:  The plastic wrapper does not need to be taken off/removed - it melts away! <<<

  • Do I need to seal over Crack Stix® or Pli Stix®? It is not necessary to go over the product with a sealer product unless it is greater than in 1/8th below the surface. If the Pli-Stix® or Crack-Stix® is level with the asphalt surface, for best results I would recommend lightly re-heating the Crack-Stix® or Pli-Stix® and broadcasting sand over the surface of the repair. This will give the Crack-Stix® / Pli-Stix® a rough texture allowing the sealer to grab onto the product better and last longer

ps5 crstx2 crstx1

TESTIMONIALS

Awesome! I ordered 60 ft of Pli-Stx from your web site on Monday, received it yesterday, awesome ship time.  I installed about 20 feet last night. The product is excellent!!!! My patio looks terrific.  Filling the joints which had old decayed material in them, with Pli-Stix makes it look new again.
You have a first class company, producing American Made Products, and giving back to the community. Thank you,
R.S. Clifton, NJ

Next best thing to Peanut Butter! I just had to tell you that your product "Pli Stix" is the next best thing to Peanut Butter. It does exactly what you explained it would accomplish. It was easy to use and performed to expectations. Thanks and congratulations on manufacturing a fine product. Very satisfied customer
.
WB, East Northport, NY

Remarkable Product! What a remarkable product Pli Stix is.  Had used it on my asphalt driveway to fill many "nuisance" cracks.  That was 3 years ago - they are still sealed.  I can't say enough about your product.
FF, Eagan, MN

Remains Flexible! In the past I have used liquid crack fillers however, the liquid fillers harden in one season. PLI-STIX seems to be more resilient. It also remains flexible with temperature change.
WN, Colorado

Translate »