Latex·ite® Pli-Stix® 30ft. MEDIUM 1/2" Black Permanent Asphalt Crack Filler / Remplit Les Fissures à Chaud

PliStix 2015
360 PliStix 2015

Latex·ite® Pli-Stix® 30ft. MEDIUM 1/2″ Black Permanent Asphalt Crack Filler / Remplit Les Fissures à Chaud

Latex·ite PLI-STIX® 30ft. MEDIUM 1/2″ Black Permanent Asphalt Crack Filler is the only PERMANENT solution to cracks on the marketplace. It is the same product seen on highways and roads but the only difference is YOU CAN APPLY IT and don’t need a 200 gallon melter to do it!

 

PLI-STIX® is permanent because it is applied with heat (a simple hand held torch) and it bonds to the sidewalls of the crack. Cracks open up because they expand and contract with freeze/thaw cycles – but PLI-STIX® will expand and contract right along with mother nature!

 

Latex·ite® 30 pi PLI-STIX® Bouche-fissures d’asphalte permanente / Le béton est la seule solution permanente à des fissures sur le marché. Il s’agit du même produit vu sur les routes et les routes, mais la seule différence est que vous pouvez l’appliquer et ne pas besoin d’un fondoir 200 gallons pour le faire!

 

PLI-STIX® est permanente, car elle est appliquée avec la chaleur (une simple main tenue torche) et ses obligations aux flancs de la fissure. Fissures ouvrir parce qu’ils dilatent et se contractent avec cycles gel / dégel – mais PLI-STIX® se dilate et se contracte à droite avec la mére nature!

 

  • Only permanent crack filler on the marketplace.
  • For Cracks 1/2″ – 1″ in diameter.
  • Hot applied, black “rope-like” filler bonds to sidewalls.
  • 30 ft. of MEDIUM PLI-STIX®
  • No VOC’s
  • Remplissage fissure Seulement permanente sur le marché.
  • Remplit les fissures jusqu’à 1/2 “(1,27 cm) de large (1” si doublé au cours).
  • Appliqué à chaud, noir (gris pas offert) “en forme de corde” obligations de remplissage à flancs.
  • 9,1 m (30 pi) de PLI-STIX®
  • Pas de COV

 

To order from our featured dealer, please visit the product page here.

 

TECHNICAL INFORMATION

  

HOW TO VIDEO
APPLICATION

PLI-STIX® is a simple and clean process. Before applying the product, it is important to thoroughly clean out the crack and remove any loose debris. Rinsing the crack and allowing it to dry will give you the best results.

Now you are ready to install the PLI-STIX®. Simply place the PLI-STIX® into the crack (do not remove the plastic wrap from the PLI-STIX®). The PLI-STIX® must be inside the crack so we recommend pushing the PLI-STIX® into the crack using a screwdriver. (*Note: If the crack is not as wide as the ½" PLI-STIX®, we recommend stretching the PLI-STIX® out...you can leave it in the sun for a while to make it easier to stretch. You can also splice it with a razor blade. You can also use a rubber mallet to help form the strip for the pavement cracks & also helped in the "wedging in" effort). If you have VERY narrow crack you may have to heat a knife with your torch so that it splices the Stix like a butter knife!

Once it's in simply light your torch (we recommend a Bernzomatic hand-held torch) and apply direct flame to the PLI-STIX® until it liquifies - this should take about 20 - 30 seconds. Allow the PLI-STIX® to set up for 20 minutes. PLI-STIX® can be sealed over once properly set up. For best results use CSX Cane TorchTM 900 as this will save you from bending over (it has a crimped end for a nice tight flame). A torch is recommended versus a heat gun.

Do not apply in wet cracks or where frost, snow or ice is present. Do not apply if the ground temperature is below 40 degrees.

>>> Reminder:  The plastic wrapper does not need to be taken off/removed - it melts away! <<<

PLI-STIX® est un procédé simple et propre. Avant d'appliquer le produit, il est important de bien nettoyer la fissure et retirer tous les débris. Rinçage de la fissure et laisser sécher vous donnera les meilleurs résultats.

Maintenant vous êtes prêt à installer le PLI-STIX®. Il suffit de placer l‘ PLI-STIX® dans la fissure (ne pas enlever la pellicule de plastique de la PLI® STIX-). Le PLI-STIX® doit être à l'intérieur de la fissure afin que nous recommandons en poussant le PLI-STIX® dans la fissure à l'aide d'un tournevis. (* Note:. Si la fissure n'est pas aussi large que la 1/2" PLI-STIX®, nous vous recommandons d'étirement, le PLI-STIX® sur ... vous pouvez le laisser au soleil pendant un certain temps pour le rendre plus facile à étirer Vous pouvez également le raccorder avec une lame de rasoir. vous pouvez également utiliser un maillet en caoutchouc pour aider à former la bande pour les fissures de la chaussée et ont également aidé à la "calage dans" l'effort). Si vous avez fissure trés étroite vous pouvez avoir à chauffer un couteau avec votre lampe torche afin qu'il relie à l'Stix comme un couteau à beurre!

Une fois que c'est dans la lumiére tout simplement votre lampe torche (nous recommandons un Bernzomatic main la torche) et appliquer la flamme directe, à la PLI-STIX® jusqu'à ce qu'il se liquéfie - cela devrait prendre environ 20 - 30 secondes. Permettre à l' PLI-STIX® de mettre en place pendant 20 minutes. PLI-STIX® peut être scellé au cours une fois correctement mis en place. Une torche est recommandée par rapport à un pistolet à air chaud.

Ne pas appliquer dans les fissures humides ou où le gel, la neige ou la glace est présente. Ne pas appliquer si la température du sol est inférieure à 4.4 Cdegrés.

ps5 crstx2 crstx1crstx3

TESTIMONIALS

Awesome! I ordered 60 ft of Pli-Stx from your web site on Monday, received it yesterday, awesome ship time.  I installed about 20 feet last night. The product is excellent!!!! My patio looks terrific.  Filling the joints which had old decayed material in them, with Pli-Stix makes it look new again.
You have a first class company, producing American Made Products, and giving back to the community. Thank you,
R.S. Clifton, NJ

Next best thing to Peanut Butter! I just had to tell you that your product "Pli Stix" is the next best thing to Peanut Butter. It does exactly what you explained it would accomplish. It was easy to use and performed to expectations. Thanks and congratulations on manufacturing a fine product. Very satisfied customer
.
WB, East Northport, NY

Remarkable Product! What a remarkable product Pli Stix is.  Had used it on my asphalt driveway to fill many "nuisance" cracks.  That was 3 years ago - they are still sealed.  I can't say enough about your product.
FF, Eagan, MN

Remains Flexible! In the past I have used liquid crack fillers however, the liquid fillers harden in one season. PLI-STIX seems to be more resilient. It also remains flexible with temperature change.
WN, Colorado

Translate »